material rate
英 [məˈtɪəriəl reɪt]
美 [məˈtɪriəl reɪt]
原材料耗用率
双语例句
- Both high material removal rate ( MRR) and smooth surface have to be achieved in primary chemical mechanical polishing ( CMP) of hard disk substrates.
硬盘盘基片粗抛光必须在较高材料去除率的基础上获得高表面质量。 - Discharge voltage, current and impulse duration have direct influence on material removal rate, but with the material removal rate rising the roundness is not always decreased.
电压、电流和脉宽主要影响材料的去除率，但大的材料去除率并不意味着高的整形效率。 - According to material biogas-producing rate of pig waste, expressions between biogas yields of piggery waste treatment and amount of pig on hand was obtained.
针对粪便污水的氮、磷和有机物浓度高的特点，开展了生物&化学工艺处理粪便污水的生产性试验研究。 - This paper studied the effect of material rate to yield in synthesis of sodium phosphocreatine. And determined the best material rate.
研究了反应物配比对磷酸肌酸钠收率的影响，确定了最佳物料配比。 - Effect of Eccentricity on Material Removal Rate in Certain Eccentricity Polishing
偏心距在偏心抛光中对去除速率均匀性的影响 - Objective: To investigate the effect of contrast material flow rate and dose on intracranial vascular spiral computed tomographic angiography ( SCTA) imaging.
目的：探讨不同对比剂用量及注射速率情况下，多层螺旋CT脑血管成像的应用效果。 - The influence of the flue ash in the preheater waste gas on the raw material rate
预热器废气中窑灰对生料率值的影响 - A theoretical model to estimate the material removal rate has been developed.
现已成功研制一个估算材料切除率理论模型。 - The hydrodynamic lubrication characteristics be-tween the wafer and pad are shown to illustrate that circular-translational-grinding facilitates increasing material removal rate.
试件与研磨盘间的流体润滑特性表明，圆平动平面研磨有利于提高表面质量和材料去除率。 - In this paper, the methods improving material utilizing rate during automobile die design development are mainly introduced.
本文主要介绍汽车模具开发中提高材料利用率的方法。 - Stand the material rate of timber species and the investigation of the relationship between factor complex relationship.
林分材种出材率与各调查因子的关系存在复杂关系。 - Only depth of cut and federate have effects on material removal rate ( MRR).
仅当切削深度、进给速度等参数值增加时，材料去除率增加； - It is a contradiction to achieve a high material removal rate and a super smooth surface in lapping of magnetic head.
在硬盘磁头抛光中加入超声波，可以提高材料去除率、降低表面粗糙度值、减小极尖沉降。 - A Study on the Technology for Enhancing the Material Utilization Rate of Tailor-welded Blank
提高激光拼焊板材料利用率的工艺研究 - The effects of catalyst roasting temperature, reaction time, reaction temperature, raw material mole rate and amount of catalyst on the coversion of acrylic acid were studied.
试验考察了催化剂焙烧温度、反应时间、反应温度、原料配比和催化剂用量对丙烯酸转化率的影响。 - The simulation of material removal rate, one of the key processes of the multi-mode combined polishing, was described in detail.
描述了多模式组合抛光的关键技术之一，材料去除率仿真模型的建立方法。 - This increased pressure drop improves the material flow rate through the flowmeter.
这个增大的压力降增大了通过流量计的材料流率。 - Experimental results show that the silicon wafer polishing with the new method on surface quality, and material remove rate are better than that of without polishing.
结果表明，该超声椭圆振动辅助抛光法对硅片抛光表面质量、材料去除率均有较显著的改善。 - Cutting power per unit material removal rate
单位材料切除率的切削功率 - Analysis on Hydrodynamics and Material Removal Rate of Circular Translational CMP; Research on Rotating Mechanism of Shaft-Disk Based on Polishing Material Machine
圆平动化学机械抛光的流体动力性能及材料去除率研究基于抛料机轴-圆盘转动机构的研究 - The grab overall structure is light and durable, offering high grabbing ratio, strong closing force and high material filling rate.
抓斗整体结构设计轻盈，抓取比大，闭合力强，物料充填率高。 - In ultrasonic machining, machining efficiency is directly effected by material removal rate.
超声加工过程中，材料的去除率直接影响加工效率。 - The higher the organic material rate, the lower the total nutrient content in granule complex fertilizer and the higher the organic matter content and organic nutrient rate in the same fertilizer.
有机原料比例越大，颗粒肥的总养分含量越低，但肥料中有机养分比例、有机质含量随之提高； - In this paper, the ultrasonic machining technology is used to machine the marble and the contrastive experiment is made with the ceramic as well. The influence of several machining parameters on the material removal rate and the accuracy is also studied.
本文采用超声波加工技术对大理石的孔加工进行了试验研究，并与陶瓷材料进行了对比试验，研究了各种加工参数对材料去除率和加工精度的影响。 - Material feeding rate has some influence on the powder dispersion and the efficiency.
进料速度对物料分散性和分级效率有一定影响，在一定范围内，进料速度对分级效率影响较大； - By studying the effecting factors of H_2O_2 insoluble guideline, it was known that the main effecting factors were the reaction control temperature and material rate.
研究了双氧水不溶物指标的影响因素，其主要影响因素是反应控制温度和物料配比，反应控制温度最好控制在800℃，物料配比（质量比）B2O3：Mg<3：1。 - Experimental study of the material removal rate.
材料去除率实验研究。 - The results showed that the C-S model is too more to contain the material strain rate effect.
结果表明C-S模型过高地反映了材料的应变率效应。 - Mathematical model is established based on the theory relation between material removal rate and electric discharge parameters.
理论分析并建立了材料去除率与放电参数之间的数学关系模型。